Mpps v16 update v183/29/2024 In fact the clone MPPS works more reliably.ģ) Just ordered one for US$99 its worth that for the tricore/boot wires to recover edc15. Restarted the laptop and used restore option to write original file back. One time my laptop shut off half way when I was writing a file on a EDC16 Octavia 2. MPPS v18 is good for VAG cars and Fiat 1.3 ddis engines. Been using it on and off for the last year with no problems what so ever. Software work okay with mpps v18 PCB here: !9Dpg3JwL!PFVR8bbMhC8HaDhBE075IP8iryOdbHDk3kkBNqmShiw MPPS v18.12.3.8 software free download, it is crack version. It works good on Windows 8 and Windows 10 both 圆4, software will only start when cable gets power from car. Be sure to run as administrator using windows 7. Then click Write, choose the file to write and wait fo a while for the progress bar to reach 100% and you are done, and as happy as i was that i have saved some $$ on buying programmers, or used ECU’s, or sending to a tuner for a fix.Here are software download resource and user reviews on MPPS V18 MAIN + TRICORE + MULTIBOOT with breakout tricore cable China Clone ECU tuning cable. Above the progress bar you will see something written in GREEN color, and you’re good to go. Click Checksum Open the file that you want to checksum, the open the file that you have read from your car before making any mods.I found this Hardly noticable, and found only after a hint in the internet after 16 hours of searching.Īfter that choose your ECU as stated in the List that opens after you choose GENERIC Navigate to where you choose brand and choose not VW or Audi etc.And before connecting the negative wire be sure to ground the bootmode pin 24 thru a 5k resistor, and remove it after aprox 15 seconds, but do not disconnect the ecu and MPPS power connections. Before connectin the +12v power supply to the proper cable as you have seen in the pictures above. This was tricky for me, but finally i got to this point and after that everything was a peace of cake. When all done and checked twice, connect your MPPS cable to PC, open software and locate the BOOTMODE wirte function.MPPS Cable Pinout: (it’s mpps v12, but out of date now is mpps v18) Prepare all the connections to the ecu and MPPS cable as shown on the picture below.Here are the picture of the chip, and the pin to be used. To the other end of the wire connect 5k resistor. For now you have to solder a wire to the pin. Here is the picture, this is what you will probably see inside the ECU case. Dont heat it too much, just to be hand warm. ![]() ![]() Warm it a little bit up, there is a sealnt which holds the housing halves pretty strong, so after warming will be easier to open it. ![]() Note: You do this on your own, and i cant be responsible for mistakes you make! So here it is in very short description, with pictures. I found this very hard to do, and while searching decided that if i succeed to recover i will do a simple instructions how to do it without asking too many dumb questions. Everyone was saying that is “simple, just write in bootmode”, “MPPS can recover almost any EDC15 ECU”, “I’ve done many times” an so on. ![]() I have searched for a solution to fix bad flashing/write disaster or error, or bricked EDC15 or whatever you call it, and got to the point where i found many info regarding how to enter bootmode, desoldering and programming with willem programmer, and found many pictures, wiring and so on.īut aparently none of them described how to do this exatcly, i mean how to write with mpps in bootmode.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |